Mastering Plumbing Fundamentals When You Install a Bathtub
Mastering Plumbing Fundamentals When You Install a Bathtub
Blog Article
The author is making a number of good points about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround as a whole in this content underneath.
Installing a bath tub isn't exactly brain surgery, yet it does call for strong plumbing, carpentry, and also sometimes, tiling abilities. Replacing an old tub with a new one is likewise a reasonably hard project. If the old tub is conveniently obtainable, the task can relocate quickly; if you have to open up a wall to get rid of the old bathtub and position the brand-new bathtub, the task is much harder. In either situation, the task is within a residence handyman's skills, although you will certainly need an assistant to vacate the old tub and also embeded in the brand-new one. See to it you have certified yourself for the job and also fit trying it. As opposed to hiring a specialist to take control of a halfway-completed job, it is far better to think about employing one prior to you begin. Chances are you might require a specialist plumber to make tube links.
This post will certainly aid you mount a brand-new tub in your shower room if you have actually currently bought a brand-new tub and do not require to change the setup of your previous water pipes.
Your tools as well as material list ought to comprise the following:
Preparing for the Setup
To start with, the sustaining framework supplied with the bathroom needs to be fitted (if required) according to the manufacturer's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is very important to ensure that if the tap features a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the faucets unit to avoid strain on the bathtub.
Fit the flexible tap connectors to the bottom of both faucets using 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet with the hole in the bath. Make use of the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you utilize every one of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom should now prepare to be fitted in its last position.
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your setup, after that the first thing you ought to do is detach the water system. After doing so, activate the faucets to drain any type of water staying in the system. The process of eliminating the existing taps can be rather troublesome because of the restricted access that is frequently the case.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the faucets. Have a towel prepared for the staying water that will originate from the pipes. As soon as the supply pipes have actually been eliminated, make use of the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from turning throughout this process. Once the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any old securing compound.
Prior to going on to fit the new taps, compare the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Mounting the Bath tub
Using both wood boards under its feet, position the bath tub in the called for setting. The wooden boards are handy in equally spreading out the weight of the tub over the area of the boards rather than focusing all the weight onto 4 little factors.
The next goal is to make certain that the tub is leveled all round. This can be attained by checking the spirit level and also readjusting the feet on the bath tub up until the level reviews level.
To mount faucets, fit all-time low of the furthest flexible tap adapter to the proper supply pipeline by making a compression sign up with; then do the very same for the other faucet.
Activate the water system and also inspect all joints and also new pipework for leaks and also tighten them if necessary. Load the tub and also check the overflow outlet as well as the regular outlet for leaks.
Lastly, repair the bathroom paneling as defined in the manufacturer's user's manual. Tiling and sealing around the bathtub ought to wait up until the tub has been used a minimum of when as this will certainly resolve it right into its final position.
Suitable New Taps
If the tails of the brand-new faucets are plastic, after that you will need a plastic connector to stop damages to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end supplies a link to the current supply pipelines.
If you require to fit a monobloc, after that you will require reducing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the placing opening in the bath/basin guaranteeing that the washers are in area in between the tap and the sink. Protect the tap in position with the maker provided backnut. When the faucet is firmly in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with typical tap connectors. The previous type should be linked to the faucet ends first, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the area where the bathroom meets the floor tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the installation can relocate enough to crack an inflexible seal, causing the water to penetrate the wall surface in between the bathroom and the tiling, resulting in issues with dampness and also possible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to blend in your fixtures and installations. They are sold in tubes as well as cartridges, and also can sealing spaces approximately a size of 3mm (1/8 inch). If you have a larger void to load, you can fill it with spins of drenched paper or soft rope. Keep in mind to constantly fill up the tub with water prior to sealing, to enable the activity experienced when the tub remains in usage. The sealant can fracture relatively very early if you do not think about this motion prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also easily offered on the market. It is advisable to fit the floor tiles using waterproof or water resistant sticky and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As an avid person who reads about Tools You Need to Install a New Bathtub , I was thinking sharing that piece of content was a good idea. You should take the time to distribute this blog entry if you enjoyed reading it. We value reading our article about Installing A Bathtub.
Prevent further damage. Report this page